Despite their good quality products, users still experience issues with the whirlpool Cabrio washer, as they do with any other good quality appliance.
This piece will help you troubleshoot some of the common Whirlpool Cabrio washing machines and restore them back to their optimum efficiency.
Common Whirlpool Cabrio Washer Issues and Fixes
There are common whirlpool problems that most users experience. Fortunately, these faults are easy to fix.
Washer Creating Unusual Noises
This problem is marked by loud noises coming from the washing machine. These noises are in different forms.
The noise can be a loud thumping sound meaning that your washer has an unbalanced load. Fix this problem by stopping the cycle and redistributing wet laundry. You would have to get rid of some clothes if your washing machine was overloaded.
If it was a clanging noise, your washing machine might not be leveled or fixed to the floor. You need to fix this issue by grounding your washing to the floor to stop any more damage.
When your washer produces a high-pitched whine, you have to conduct extensive research to determine the exact cause of the noise.
Use your owner’s manual to know how to navigate the internal parts of your washing machine. You can also get a repair manual on the whirlpool site that you can use for the same cause.
Remove your washer’s outer housing and inspect the nuts holding the pulley in place. You might have to tighten the nuts. It this solution does not work; you will have to replace your washer’s bearings.
Lid Lock Problems
This problem occurs when your washer’s lid lock but unlocks hence stopping the start of a new cycle.
Your washer’s lid switch/latch does not engage when it is dirty. Dirt prevents the latch from making proper contact to prompt your washing machine to start a new cycle. Use a cotton swab dipped in isopropyl rubbing alcohol to clean every contact area on your washing machine’s lid.
You can also unplug your washer from its power source to reset the control panel of the washing machine. Connect your washing machine back to its wall socket to examine if the problem has been resolved.
If your washer’s door produces a sound similar to what it makes when engaging but does not engage, you need to conduct a full diagnosis on the appliance. The washing machine might have a bigger problem. Use this procedure to run the test:
Put your washing machine on standby mode. To achieve this, you need to plug the washer into its power socket and turn off all its indicators. However, you can leave the clothes done or clean indicator on. Choose any button other than Start, Power, or Stop and follow the steps listed below using your button of choice.
- Press the button down for three seconds
- Release the button for three seconds
- Hold the button, again for three seconds
- Release the button, again for three seconds
- Press it one last time for three seconds
- Release it for the last time
All the indicators in your washing machine’s console will light up for at least five seconds. Eighty-eight of these indicators will show, in their estimated time remaining, a two-digit display showing that your washer’s diagnostic mode has been successfully entered.
If your washer’s indicator fails to display as explained above, then the press and release process may not have been performed inside the required timeframe for successful entry. Repeat this procedure using a different button to ensure that the button used earlier was not the reason for the failure.
Your washer’s program will look for saved error codes. Once the diagnostic test is complete, you may choose to compare your washer’s fault code displayed to know the exact repairs needed to be done on your washing machine.
Washer Won’t Start
This problem mostly results from a faulty start button on your washer’s control panel. The start button is not working, but the rest of the lights in your washer turn on. Follow these steps to troubleshoot and fix your washing machine.
Remove your washer’s control panel to conduct a diagnosis on your appliance. You need to use your repair manual when removing the control panel to ensure you follow the right steps.
Examine the panel for any broken or loose pieces. In some cases, small plastic pieces break off behind your washer’s start button and hinder it from powering.
Use a voltage meter (view on Amazon) to examine all the wiring in the control panel. Sadly, if the main controller/CCU or timer fails, the entire control panel of your washing machine should be replaced.
Breaking Down the LD Error Code
An LD code shows on the display screen in the course of a spin cycle. This error code indicates a long drain.
When the LD code shows, your washing machine stops running. When this error code shows on your washing machine’s display, then your appliance’s drain line might be clogged. It might also indicate an obstruction in your washer’s pump. Correct this problem using these steps.
Clean any obstruction or lint that might be clogging your pump filter.
Switch off your washer’s water connection and unhook your appliance’s drain line from it’s the main washer. Keep a bucket close to trap any spill. Finally, clean the line by forcefully streaming water through it or by using a long brush.
If these solutions to not fix your washer and restore it back to its optimum efficiency, you may need to replace the water pump.
Washing Machine Produces a Burning Plastic Odor
You will know that this problem exists when your washer produces a smell of burning rubber or plastic.
When your washer emits this smell, you need to take immediate action. Begin by unplugging the washing machine from its power source and open its outer housing.
Search for discoloration. There is a possibility that your washer’s rubber drive belt (view on Amazon) is faulty. If this belt slips, breaks or stretches, it can lead to friction and produce a burning smell. In most cases, it is a smell of burning rubber. You should replace the belt.
If your washer’s belt shows no sign of weakness, the appliance might have an electrical issue, especially with its transmission, control panel, or motor.
If this is the case, you might have to seek the services of an appliance specialist since this is a more advanced problem. You will have to replace all the damaged parts of the washer.
Avoid using the washer until you repair all the damaged parts of your washer.
Washer Leaves Deposits on Dark Clothes
This problem often occurs on washers even when you change detergents.
If your washer leaves the deposits in winter, it might be as a result of incomplete dissolving of powder detergents because of the extremely cold water temperatures. Switch your washer to warm water temperature cycles.
If the frequency in which these deposits occur increases, you should clean your washing machine.
One of the disadvantages of using high-efficiency washing machines versus using a standard machine is that you will not have to use large amounts of water to flush detergents from your washer and soil residue, which ends up clinging to your washing machine.
Therefore, you need to clean your washer to remove the accumulation, which is redepositing on your clothes.
Rust Patches on the Lid of Your Washing Machine
This problem presents itself as rust patches in the inner parts of your Cabrio washer lid.
Rust patches on the lid never disappear. They only grow in size unless you fix them. They may also transfer rust stains on to your clothes. Using distilled white vinegar and a paste of baking soda, remove as much of the rust growing on your appliance as possible.
You can also use lemon juice in place of distilled white vinegar. Mix enough lemon juice or distilled white vinegar with one-quarter cup of baking soda to make a very thick paste.
Apply the paste over the rusted lid area. Use a soft piece of cloth to remove all the loose rust particles from the lid. Repeat this process severally as you rinse the area using clean water after each rub or treatment.
Immediately all the loose rust particles are removed fix the rusted area using appliance paint according to the product directions.
Other than these issues, there are some problems that may arise due to the use of the wrong products. Therefore, you need to use only the right soap, in this case, the high efficiency (HE) soap.
Even though this soap is expensive, it will help you get clean clothes out of every spin cycle. When you do not use HE soap, you risk getting clothes that are not satisfactorily clean, bad tab bearings, and error codes showing on your washer’s display screen.
Fortunately, Whirlpool Cabrio washer has a self-diagnostic mechanism which shows error codes on its display screen. These error codes correspond to specific faults within your washer.
Therefore, you can fix the issue as a DIY project purely based on the description of your owner’s manual about the error code. Some of the most common error codes include:
LF error code (F30) – Long Fill
LF shows on your washer’s display screen when the levels of water do not change over a given period after all the valves are switched on or when water is released from the drum, but the washing machine’s control panel fails to detect the change in water level.
When this happens, you need to inspect the connection of your water supply and ensure it is switched on.
You also need to ensure the screens are correctly plugged in. Lastly, if the water is flowing into your washer’s tub, inspect the appliance’s pressure hose connection to the motor control.
oL error code (F70) – Overloaded
The oL error code shows on your washing machine’s display screen when the appliance’s motor control detects a heavier than expected load size.
Correct this problem by opening the lid of your washing machine and remove excess clothes from the appliance. Restart the appliance and observe if it works as expected.
These are the common problems that you will experience with the Whirlpool Cabrio washing machine. These problems can be diagnosed and fixed easily using your owner’s manual and a keen eye to detail.
However, if you do not feel comfortable working on your appliance, call an appliance repair technician to troubleshoot and fix your washer. Always remember to take all the necessary precautionary measures when working with electrical appliances.
FAQs
Why does my Whirlpool Cabrio washer keep giving me an uL code? ›
If uL (unbalanced load) appears in display, the load is out of balance. The washer is running a load-balance correction routine. Allow the washer to continue. If the dial is flashing and the washer has stopped, redistribute the load, close the lid, and press START/PAUSE.
How do you reset the sensor on a Whirlpool Cabrio washer? ›Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset. You can run a test load without any clothing to ensure that the reset worked.
Why is my Whirlpool Cabrio washer not filling with enough water? ›One common reason for a Whirlpool washer not filling with water is that the water inlet valve is not open or is clogged. The water inlet valve supplies water to the washer, and if it's not open or does not supply enough water, your Whirlpool washer will not fill up.
What is the life expectancy of a Whirlpool Cabrio washer? ›This machine is not over worked or overloaded. It does not do more than the average 8 loads of laundry per week that whirlpool statistics suggests an average household does. Whirlpool also says the lifespan of a Cabrio washer is 11 1/2 years, that's comical, if you're easily entertained by bad jokes.
What brand of washer has the least problems? ›What brand of washing machine is most reliable? Whirlpool, LG, and Samsung are the most reliable brands of washers. Yale Appliance found that less than 7% of the sales of these units required servicing. J.D. Power also ranks Samsung and LG as the highest-ranking manufacturers in customer satisfaction.
How do I fix the LF code on my Whirlpool Cabrio washer? ›LF in the display
Check the water inlet hoses to be sure they are not clogged or kinked. You may also need to check the screens on the washer water inlet valve. This means shutting off the water supply, and disconnecting the water inlet hoses from the washer.
If you notice shaking, try to load fewer clothes and ensure items are evenly dispersed throughout the basket to equalize weight inside the washer. You can also try adding other items to help equalize weight inside the basket to help stop the shaking.
How do I reset my Whirlpool control panel? ›Turn off the washer on the control panel. Unplug the washer for twenty seconds. Turn on the washer. If the process has worked, your washer will now be reset.
What are the codes for a Cabrio washer? ›Fault Code | Washer Problem |
---|---|
uL (none) | Unbalanced load |
oL (F70) | Overloaded |
Sd (F71) | Suds Detection |
lid (F81) | Open/Close Door Lid |
You could have a faulty lid or water level switch, or your hot and cold water supplies could be turned off or have kinks in the hoses. A clogged water inlet screen or a malfunctioning electronic control could also be the reason a washer isn't filling with water.
How do I get my Whirlpool washer to fill with more water? ›
If you would like to add the maximum amount of water to your wash cycle, turn the Water Level knob to the Deep Water Wash setting. NOTE: Expect longer cycle times due to extended fill times when using the Deep Water Wash option.
How good is the Cabrio washer? ›Works well but valves are very loud
Posted 7 years ago . Overall the Cabrio washer is a quality washer. It does a very good job on clothes and has a large capacity. The one drawback is the noise from the water control valves.
If the washer has a minor failure such as a bad lock on the lid or door, it's usually better to repair the washer instead of replacing it. Completing a minor repair on a well-maintained washer with more than 8 years of expected useful life remaining is typically more economical that replacing the washer.
How do you run a diagnostic on a Whirlpool Cabrio washer? ›Choose any one button on the washer's console except Power, Start, or Stop. Press/Hold 3 Seconds - Release 3 Seconds - Press/Hold 3 Seconds - Release 3 Seconds - Press/Hold 3 Seconds. 4. If there are any saved fault codes they will be displayed.
What washers do repairmen recommend? ›Appliance repair technicians and our product experts agree: Whirlpool is the most reliable washing machine brand in the U.S.
Which is the number one brand in washing machine? ›Samsung is a very renowned washing machine brand in India. It features bubble storm, dual storm, hygiene steam, and digital inverter technology. With 3 years of warranty on the product and 12 years of warranty on the motor, this product offers a 700 rpm speed and ten wash programs for washing clothes effectively.
What does FL Lo code mean on Whirlpool washer? ›The F8 E1 or Lo FL error code means your washer is not detecting the correct amount of incoming water. If the washer has an F8 E1 error or LO FL error, the door may be locked, and the control may be unresponsive.
What does the code FL mean on a Whirlpool washer? ›Possible Solutions. The F8 E1 or Lo FL error code means your washer is not detecting the correct amount of incoming water. If the washer has an F8 E1 error or LO FL error, the door may be locked, and the control may be unresponsive.
What does E3 and F5 mean on a Cabrio washer? ›The F5 E3 alert indicates there is issue with the lid lock. Do not force the lid open, as permanent damage could occur. Remove any objects from the lid and clear any obstructions. Touch POWER to exit cycle, then touch POWER again to release lid.
How do I know if my washer drum is off-balance? ›If the washer is unbalanced, you will likely find that it does not wash or spin as well as it should. An unbalanced washer will also often trigger an error code that will disrupt the washing cycle and potentially render the washer unusable until rebalanced.
How do you know if your washing machine is unbalanced? ›
If your washing machine is reaching its spin cycle and that is manifesting in it making loud banging noise, then it is likely that the machine is out of balance in some way. When this happens, the tub of the washer will begin to bang against the sides of the washer, creating the noise.
How do you reset an unbalanced washing machine? ›Top-loading washers automatically adjust to level. If something has shifted, you can relevel a top-loading washer by tipping the washer forward, then placing it back on the floor. Front-loading washers level by turning a leg to raise or lower it.
What buttons do you press to reset a Whirlpool dishwasher? ›Some models require you to shut off the power to the dishwasher either by unplugging it or shutting off the circuit breaker. Others are reset by pressing and holding the Start/Reset button on the control panel, then waiting a few moments before attempting to start a wash cycle.
What is a powerwash reset? ›A Powerwash factory reset erases all the information on your Chromebook's hard drive, including your settings, apps, and files. The factory reset won't delete any of your files on Google Drive or an external hard drive. Before performing the reset, back up your files on Google Drive or an external hard drive.
How do I run Whirlpool diagnostic mode? ›- Washer lid should lock ="done" + "lock"
- Washer cold valve should open ="spin" + "lock"
- Washer hot valve should open ="spin" + "done" + "lock"
- Pause 5 seconds ="rinse" + "lock"
- Pause 5 seconds ="rinse" + "done" + "lock"
- Pause 5 seconds ="rinse" + "spin"+ "lock"
Error Code | Error |
---|---|
Sud or Sd | There are too many suds in the washing machine. |
F5 E2 | The door is not locking properly. |
F7 E1 | Indicates a motor speed sensing error, |
F8 E1 or LO FL | The washer is sensing a low flow of water. |
- Unplug the washer for 1 minute from the electrical outlet.
- Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid. ...
- The motor has now been reset and is ready for you to start a cycle.
If your Whirlpool washer won't agitate but will spin, you might need to replace the repair kit. The washer agitator repair kit houses the agitator components that are most likely to become damaged, wear out, or fail. If any of the parts are worn out, stripped, or defective in any way, then it's time to replace the kit.
What does E1 and F3 mean on a Cabrio washer? ›The F3 E1 alert indicates the washer can't detect the water level. There may be an issue with the appliance control unit or associated wiring.
What does F5 and E2 mean on a Cabrio washer? ›The F5 E2 alert indicates the washer can't engage the lid lock because there may be an obstruction in the lid lock area. Please check the lid lock area and remove any objects in that area. Also verify there are no clothing items in the way.
Why is my washer not getting all the water out of my clothes? ›
Typically, this means checking the drain hose, drain pump, and any filters or coin traps that could be blocked. Other causes of clothes still being wet after the spin cycle include an unbalanced washer, using the wrong detergent, or a worn or loose drive belt.
What are the most common problems on a Whirlpool washing machine? ›- Washer Making Unusual Noises. ...
- Washer Won't Start. ...
- Washer Lid Won't Lock. ...
- LD Error Code Appears. ...
- Washer Leaves Deposits on Dark Clothes. ...
- Washer Has a Burned Plastic Odor. ...
- Rust Spots Appear on Washer Lid.
There are only 2 places where water can get into a washing machine's drum. Either seeping through a faulty water valve, or coming in through the drain hose. It's impossible for water to get in any other way. If the water is very clean, it might be coming in through a water valve.
Can I manually add water to washer? ›Manually fill the washer with your stored water using a bucket or whatever system you have chosen until the clothing is completely covered with water. Take care not to spill water on the top or over the sides of the drum. This may damage electrical components of the machine. Close the lid and switch the machine on.
Is a washing machine supposed to fill all the way up with water? ›Clothes should be distributed evenly and loosely inside the machine. Even a large load of laundry should not fill the washer tub more than three-quarters full.
Why does my washing machine only fill half way? ›Weak water flow to your washer could mean your hot and cold valves aren't turned on all the way. Some valve handles need to be turned as far as you can counterclockwise to fully open. Newer valve handles must be turned 90 degrees so they line up with the hoses going to the washer.
Which Whirlpool machines are being recalled? ›The company said models WMAQC641PUK, WMAQG741PUK and WMFG741GUK will be added to the recall list, and that it would contact all owners of the machines it is aware of. The model numbers can be found in the recess inside the door or on the back of the appliance.
What usually fails on a washing machine? ›A washing machine not draining is one of the most common problems we encounter. It can be caused by one of the following: - The drain hose or pump is clogged with a small item of clothing, residual gunk or other debris. - The washer is malfunctioning and not engaging the drain/spin cycle properly.
What is the average life of a Whirlpool washer? ›The average life of a washing machine ranges from 10 to 13 years, although some brands can manufacture washing machines with an even longer lifespan than the average appliance.
Does Whirlpool honor their warranty? ›What does the Whirlpool® appliance warranty cover? Your Whirlpool® appliance warranty will cover most of Factory Specified Replacement Parts and repair labor to fix any defects in materials and workmanship that existed within one year of when your appliance was purchased.
Will Whirlpool replace my washing machine? ›
Most products come with a full warranty that covers your appliance for one year from the date of purchase. The company promises that it will pay for replacement parts and labor to correct any manufacturing defect in the machine that results from defective materials or workmanship.
Is it worth repairing a 5 year old washing machine? ›Replace: An older machine that breaks down frequently and has needed several repairs in the past few years could keep hurting your wallet. Consider making the switch to a new appliance if your old one is more than 50% through its life expectancy and the cost of a repair would be more than half the cost to replace.
Is it worth fixing a 10 year old washing machine? ›Consumer Reports recommends replacing any appliance that's more than eight years old, unless it's a high-end model and has a particular appeal to you. Others suggest replacing any top-loading washer manufactured in 1999 or earlier.
Is it worth fixing a washing machine? ›If your washer needs a major repair such as a new motor, tub or transmission, you're often better off replacing the washer rather than repairing it; a major repair often costs more than half the price of a replacement washer.
Why will my washing machine not drain and spin? ›If your washer won't drain or spin, the water level control may be faulty. Open the machine's control panel and look for a plastic tube attached to the water level valve. If it's clogged, clear it out with vinegar. If the valve itself is corroded, it may need to be replaced.
What would cause a washer to not spin or drain? ›If the washer won't drain or spin, either something is stuck in the washing machine drain hose or pump, or the pump is broken. If a washer won't drain or spin, the fix is simple if you're even just a little bit handy with tools.
Why won't my washing machine finish its cycle? ›Some of the most common faults that will make your washer stop mid cycle include thermostat failure, problems filling up with water for the rinse cycle, or even pump problems that prevent your washer from draining. One thing that you can check yourself is the lid switch.